Probook 4520s Drivers
Introduction
If your HP ProBook 4520s shuts down without warning, you may have a hard drive error and need to replace the hard drive.
- HP ProBook 4520s - 15.6' - Core i3 380M - 3 GB RAM - 320 GB HDD overview and full product specs on CNET.
- Bluetooth not working on Windows 10 upgrade (HP Probook 4520s) Windows 10 upgrade and Bluetooth. I was unable to find new drivers for my HP Probook HP4520s Buetooth Motorala BC4 driver.
Find support and troubleshooting info including software, drivers, and manuals for your HP ProBook 4520s Notebook PC.
- Phillips #1 Screwdriver
- Spudger
- Metal Spudger
No parts specified.
Flip the 4520s upside-down with the front toward you.
Push the two latches below the battery inwards at the same time.
Remove the battery by holding the latches and sliding the battery away from you.
Use a Phillips #1 screwdriver to remove three 2mm screws where the battery was located.
Flip the 4520s over and rotate it so the back is facing you.
Use a metal spudger to peel off two rubber caps located on either side of the battery port.
Use a Phillips #1 screwdriver to remove the 3mm screws behind the caps.
Rotate the 4520s and then open it with the screen facing you.
The switch cover is located above the keyboard. Push the switch cover away from you until it comes loose from the 4520s.
Lift the switch cover away from the 4520s and set it aside.
Use a Phillips #1 screwdriver to remove the two 7mm screws located on either side of the keyboard panel.
Slide the keyboard panel away from you to free it from the 4520s.
Do not yank the keyboard panel away from the 4520s. This may damage the cable.
Gently raise up the keyboard and flip it over to reveal a ribbon cable.
Release the ribbon cable by carefully lifting the black tab upwards, one side at a time.
Remove the cable and lift the keyboard panel up. Set it aside.
When reassembling, feed the ribbon cable into the port. Press down on the tab to pinch the cable in place.
Use a Phillips #1 screwdriver to remove the three 3mm screws along the top of the palm rest.
Slide the palm rest to the right to release it and then rotate it back gently.
Do not yank the palm rest away from the 4520s. This may damage the cable.
Release the ribbon cable by opening the black hinge on the port using a spudger.
Remove the cable and set the palm rest aside.
The hard drive is contained in the housing on the lower right.
Remove two 5mm screws on the left using a Phillips #1 screwdriver.
Fully loosen the captive screw on the right using a Phillips #1 screwdriver.
Disconnect the hard drive by pulling the tab to the right.
Lift the housing out from the 4520s.
Use a Phillips #1 screwdriver to remove the four 3mm screws on the sides of the housing.
Lift the housing away from the hard drive.
The hard drive is 2.5'.
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
26 other people completed this guide.
Embed this guide
Choose a size and copy the code below to embed this guide as a small widget on your site / forum.
Preview
Introduction
If your HP ProBook 4520s shuts down without warning, you may have a hard drive error and need to replace the hard drive.
- Phillips #1 Screwdriver
- Spudger
- Metal Spudger
No parts specified.
Flip the 4520s upside-down with the front toward you.
Push the two latches below the battery inwards at the same time.
Remove the battery by holding the latches and sliding the battery away from you.
Use a Phillips #1 screwdriver to remove three 2mm screws where the battery was located.
Flip the 4520s over and rotate it so the back is facing you.
Use a metal spudger to peel off two rubber caps located on either side of the battery port.
Use a Phillips #1 screwdriver to remove the 3mm screws behind the caps.
Rotate the 4520s and then open it with the screen facing you.
The switch cover is located above the keyboard. Push the switch cover away from you until it comes loose from the 4520s.
Lift the switch cover away from the 4520s and set it aside.
Use a Phillips #1 screwdriver to remove the two 7mm screws located on either side of the keyboard panel.
Slide the keyboard panel away from you to free it from the 4520s.
Do not yank the keyboard panel away from the 4520s. This may damage the cable.
Gently raise up the keyboard and flip it over to reveal a ribbon cable.
Tekken 6 psp rom download. Release the ribbon cable by carefully lifting the black tab upwards, one side at a time.
Remove the cable and lift the keyboard panel up. Set it aside.
When reassembling, feed the ribbon cable into the port. Press down on the tab to pinch the cable in place.
Use a Phillips #1 screwdriver to remove the three 3mm screws along the top of the palm rest.
Slide the palm rest to the right to release it and then rotate it back gently.
Do not yank the palm rest away from the 4520s. This may damage the cable.
Release the ribbon cable by opening the black hinge on the port using a spudger. Free music software windows 7.
Remove the cable and set the palm rest aside.
The hard drive is contained in the housing on the lower right.
Remove two 5mm screws on the left using a Phillips #1 screwdriver.
Fully loosen the captive screw on the right using a Phillips #1 screwdriver.
Disconnect the hard drive by pulling the tab to the right.
Lift the housing out from the 4520s.
Use a Phillips #1 screwdriver to remove the four 3mm screws on the sides of the housing.
Lift the housing away from the hard drive.
The hard drive is 2.5'.
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
26 other people completed this guide.
Embed this guide
Hp Probook 4520s Drivers Bluetooth
Choose a size and copy the code below to embed this guide as a small widget on your site / forum.